5-Speed Transmission Swaps For Chevy Inline Six Engines

Put a modern T5 behind your 216, 235, or 261 Stovebolt.

On of the most popular upgrades for Advance Design trucks, is the installation of a late-model 5-speed T5 transmission in place of the original 3 or 4 speed gearboxes.

Choose your T5

The Borg-Warner T5 transmission was widely used by various auto manufacturers over the years, but we are primarily interested in those used in the Chevy S10 trucks and Astro vans from the mid 80’s. These particular gearboxes use the same bolt pattern as your Chevy Stovebolt engine, and have manual speedometer outputs capable of driving your original (or aftermarket) speedo.

The main thing to consider in choosing your T5 is gear ratios. If you are changing the gearing in your rear, you will want to keep that in mind. Use a calculator to find the best ratios for you, while taking engine RPMs, differential ratios, and tire size into consideration.

Please see our T5 Information Page for information on gear ratios and Borg-Warner part numbers.

T5 transmissions can be found at junkyards, but you may get find a better deal in the local classifieds or an online auction.

Get Ready

A 1986 T5 in a 1951 Chevy pickup with a 261 engine.

A 1986 T5 in a 1951 Chevy pickup with a 261 engine.

The Chevy T5 gearboxes will bolt right up to your Stovebolt, but you will need to do a little massaging to get everything to mesh. Firstly, you will need to find a clutch disc with the correct diameter and the right number of splines to fit the input shaft of your T5. Most T5’s use a 27-spline input shaft, and you can buy clutch discs to fit this from most local auto parts stores (Napa, Advance, etc…). Measure your original clutch disc and try to find something of the same diameter.Clash of Clans Online Hack and Cheat

The input shaft on your T5 will be slightly longer than the original transmission. Use a feeler gauge to precisely measure the difference. You can either trim the extra length off the end of the input shaft, or create a simple spacer to fit between the transmission and bellhousing.

Finally, remove the T5 bellhousing from the transmission (if you have it) and drill out the 13mm holes in the transmission with a 1/2″ drillbit to allow the bellhousing bolts to fit.

Install It

Your T5 should now bolt up to your Stovebolt bellhousing. You should be able to use the original throwout bearing, clutch fork, and pilot bearing with your T5. With the right preparation and a little luck, the whole thing will go together and you’ll have a working clutch!

Finishing It Up

The T5 gearbox is a few inches longer than the original transmission, so you will need to make some modifications to the driveshaft. Many people choose to replace or upgrade the rear axle at the same time and getting a custom driveshaft built to fit, but you may be able to get your existing driveshaft shortened at a driveline shop. You will also need to find a slip yoke for your T5 if you don’t already have one. This may also be a good time to eliminate the Torque Tube if you’re interested.

Comments (17)

  1. jim

    4 years ago

    i have a 1952 chevy half ton 3100 truck. that i want to change trans. and rear end, i found this site very helpful . thanks for the info . jim

  2. charles reynolds

    4 years ago

    can the s 10 trany be used on a 1948 6400 2 ton and if so do you use a v6 or a 2.8 transmission i need better gears rear is a 6.17 in high 8.10 in low not verry fast any info would be verry thankfull thank you charles

  3. michael

    4 years ago

    I have a T-5 from a Camaro with the shifter at the end of the casing. I want to put it in my 67 chevy truck. I can replace the bench seat with some buckets I have but will that shifter be to far back? Help

  4. Philip Dumais

    4 years ago

    If I was to swap out the current tranny in a 54 gmc truck for this five speed, would it help with my milage? if so approximately how many miles per gallon would the truck get, if it had the inline 6 engine

    • Jonathan Groff (Admin)

      Jonathan Groff (Admin)

      4 years ago

      As a point of reference, my ’51 with a 261, T5, and updated rear axle with 3.73 gears has a top speed of 88MPH and averages 18MPG.

  5. Jim

    4 years ago

    I have a 1952 GMC truck can I install a T5 trans to a 228 6 cyl ? if so please give info how to thank you

  6. James Hughes

    4 years ago

    I have a 1938 with 216 three on floor truck. Would like to install a T5 and change rear axle gears . Anything I should know of would help.

  7. Al falke

    4 years ago

    This information is a great help, thanks

  8. Glenn Saborosch

    4 years ago

    Will the T-5 floor shift come through the floor at the same place as the original shift lever?

  9. William Zappa

    3 years ago

    I have a 52 Chevy 3100 but someone put a 307 V8 in it. Can I still use a T5trans? If so anything elose need to change? Thanks

  10. mike

    3 years ago

    can I use a 91 s10 5speed on a 1955 235, and can I change the electric speedo to a manual?

  11. dave wooster

    3 years ago

    thank you for your info… i have a 51 3100 that needs an up grade sounds like the ideal up grade…

  12. Terry G.

    2 years ago

    Is it possible to remove the torque tube and still use the original drive shaft in this application? Thanks

  13. Jim Bo.

    2 years ago

    Can I get a t5 to bolt up to a inline 6 a 194 cu.in. Eng. 3.2 l.

  14. omar

    1 year ago

    Got 79 gmc 250 motor the t5 fits,??

  15. Phil W

    1 year ago

    my ’50 3100 4 speed is tired, I’d like the T5 tranny but an open drive shaft and modern rear. My rims are 6 lug

  16. Russell Blankenship

    1 year ago

    I’ve got a 55 4100 cab over going to put a 292 or 302 if I can find one But we’ll this T 5 work for this Sat up Thanks

Comments are closed.